{"product_id":"winch-power-interrupt-kit-warn","title":"Winch Power Interrupt Kit | WARN","description":"\u003ch2\u003eCabin-Controlled Power for a Compatible Winch Circuit\u003c\/h2\u003e\n\u003cp\u003eThe WARN Power Interrupt Kit adds a switched disconnect to a compatible accessory battery lead. Its solenoid handles the main power connection while a separate cabin switch controls the solenoid. For a Bronco owner planning a winch installation, this separates the power-enable function from the winch's normal direction controls. The supplied switch can be mounted inside the vehicle, giving the driver a way to enable or disable the connected circuit without using a manual switch beside the battery.\u003c\/p\u003e\n\u003ch3\u003eWhat the Power Interrupt Kit Controls\u003c\/h3\u003e\n\u003cp\u003eThis kit controls whether power reaches the connected accessory circuit. It does not replace the winch's wired or wireless remote, operate the clutch, or command the drum to pull in and out. Turning the interrupt switch on makes power available; the accessory is then operated through its own controls. WARN recommends leaving the interrupt switch off until the attached accessory is ready to be used.\u003c\/p\u003e\n\u003cp\u003eThe switch and solenoid serve different jobs. The heavy battery lead carries the accessory supply through the solenoid, while the smaller control wiring operates the switching circuit. A factory overhead AUX switch must not carry the winch motor's main current. Using an existing vehicle switch requires the installer to verify the control circuit and adapt the wiring correctly; this is not a supplied Bronco-specific plug-in harness.\u003c\/p\u003e\n\u003ch3\u003eParts for the Installation\u003c\/h3\u003e\n\u003cp\u003eWARN supplies the solenoid, a battery lead, an illuminated dash switch, control wiring, and mounting hardware. The manufacturer's installation sheet identifies an 18-inch red 2-gauge battery cable, switch mounting pieces, protective boots, and a fused switch lead. Those components support the interrupt installation. A winch, its direction-control system, and a bumper mounting plate are separate purchases.\u003c\/p\u003e\n\u003cp\u003ePlan the mounting location before choosing the cable route. The solenoid needs a supported position, and the connections need clearance from surrounding metal and moving parts. Check whether the supplied lead reaches the intended installation without tension. An existing winch installation may require additional appropriately specified cable or connection hardware; the kit is not a promise that every custom routing layout needs no extra parts.\u003c\/p\u003e\n\u003ch3\u003eBronco AUX-Switch Integration\u003c\/h3\u003e\n\u003cp\u003eThis is a universal electrical accessory rather than a direct-fit body component. Door count, roof type, and bumper style do not establish electrical compatibility. On a Bronco with overhead AUX switches, the installer must confirm the selected circuit's behavior, wiring requirements, and suitability for the solenoid control circuit. Follow the vehicle and WARN instructions rather than substituting wire colors between different manufacturers.\u003c\/p\u003e\n\u003cp\u003eFor a DV8 12,000 lb winch, compatibility with this particular interrupt kit must be checked against the winch's electrical requirements and the interrupt solenoid's ratings. A winch's rated pulling capacity does not specify the electrical demand at every load. We have not established manufacturer approval for that cross-brand combination, so this listing does not present it as a guaranteed match.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eWARN\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManufacturer part\u003c\/th\u003e\n\u003ctd\u003e62132\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSupplier reference\u003c\/th\u003e\n\u003ctd\u003eW3662132 \/ FB73867\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFunction\u003c\/th\u003e\n\u003ctd\u003eSwitch-controlled interruption of a compatible accessory battery lead\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVehicle application\u003c\/th\u003e\n\u003ctd\u003eUniversal; wiring and mounting adaptation required\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSwitch\u003c\/th\u003e\n\u003ctd\u003eIlluminated dash switch included\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstall time\u003c\/th\u003e\n\u003ctd\u003e2 Hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWarranty\u003c\/th\u003e\n\u003ctd\u003e1-Year Limited\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePower interrupt solenoid\u003c\/li\u003e\n\u003cli\u003e18-inch red 2-gauge battery lead\u003c\/li\u003e\n\u003cli\u003eIlluminated dash switch with mounting bracket and plate\u003c\/li\u003e\n\u003cli\u003eControl wiring, including a fused switch lead\u003c\/li\u003e\n\u003cli\u003eTerminal boots, mounting hardware, and instructions\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"WARN","offers":[{"title":"Default Title","offer_id":67959108796490,"sku":"FB73867","price":102.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/0860\/6794\/files\/62132_warn-power-interrupt-kit_0630401f-7982-462a-a289-87b7d7b57ab5.webp?v=1794438226","url":"https:\/\/broncoforge.com\/products\/winch-power-interrupt-kit-warn","provider":"BRONCO FORGE","version":"1.0","type":"link"}